Document
  • Product
    01.

    Battery Management Systems

    Low Voltage

    FS-LT CT-Safe CT-Lite CT-Lite + 50A CT-Lite + 80A

    High Voltage

    FS-XT HP Safe
    02.

    Other Advanced Electronics

    Power Management

    SB-PR-I

    Telematics

    IoT
    03.

    Upcoming Projects

  • Applications

    2-Wheelers

    2W- Bike, Moped, Kick Scooter, and E-Cycle

    3-wheelers

    3W- E-Auto

    4-Wheelers

    4W- Electric Car, Golf Cart

    Outdoor Powered Equipment

    Outdoor powered equip- Lawn Mower, Construction Machinery

    Unmanned Aircraft System

    Unmanned Aircraft System- Logistics & delivery drones, Agriculture & Mapping UAVs

    Industrial Application

    Industrial Application- Forklifts, Excavators, Mining equipment, Robots

    Energy Storage

    Energy storage- BESS

    AGV

    AGV- Cleaning machines, Warehouse robots

    Commercial Vehicles

    CV- Bus, Truck, Car, Golf cart

  • Company
    01.

    About Us

    02.

    Careers

    Latest Blog

    Maxwell’s Path to BMS Reliability: A Comprehensive Journey

  • Insights
    01.

    Blogs

    02.

    Case Studies

    Latest Blog

    Maxwell’s Path to BMS Reliability: A Comprehensive Journey

  • Ecosystem
Get in touch
Document
  • Product
    01.

    Battery Management Systems

    Low Voltage

    FS-LT CT-Safe CT-Lite CT-Lite + 50A CT-Lite + 80A

    High Voltage

    FS-XT HP Safe
    02.

    Other Advanced Electronics

    Power Management

    SB-PR-I

    Telematics

    IoT
    03.

    Upcoming Projects

  • Applications

    2-Wheelers

    2W- Bike, Moped, Kick Scooter, and E-Cycle

    3-wheelers

    3W- E-Auto

    4-Wheelers

    4W- Electric Car, Golf Cart

    Outdoor Powered Equipment

    Outdoor powered equip- Lawn Mower, Construction Machinery

    Unmanned Aircraft System

    Unmanned Aircraft System- Logistics & delivery drones, Agriculture & Mapping UAVs

    Industrial Application

    Industrial Application- Forklifts, Excavators, Mining equipment, Robots

    Energy Storage

    Energy storage- BESS

    AGV

    AGV- Cleaning machines, Warehouse robots

    Commercial Vehicles

    CV- Bus, Truck, Car, Golf cart

  • Company
    01.

    About Us

    02.

    Careers

    Latest Blog

    Maxwell’s Path to BMS Reliability: A Comprehensive Journey

  • Insights
    01.

    Blogs

    02.

    Case Studies

    Latest Blog

    Maxwell’s Path to BMS Reliability: A Comprehensive Journey

  • Ecosystem
Get in touch
Client Support
1-800-356-8933
Get in touch
  • Products
    • CT-Lite
    • CT-Lite+
    • CT-Lite+ 80A
    • CT-Safe
    • FS-LT
    • FS-XT
    • HP-Safe
    • SB-PR-I
    • TCU
  • Applications
    • 2-wheelers
    • 3-Wheelers
    • 4-Wheelers
    • Automated Guided Vehicles
    • Energy Storage Systems
    • Industrial Applications
    • Outdoor Powered Equipment
    • Passenger and Commercial Vehicles
    • Unmanned Aircraft System
  • Company
    • About
    • Careers
  • Resources
    • Case studies
  • Eco System
  • Products
    • CT-Lite
    • CT-Lite+
    • CT-Lite+ 80A
    • CT-Safe
    • FS-LT
    • FS-XT
    • HP-Safe
    • SB-PR-I
    • TCU
  • Applications
    • 2-wheelers
    • 3-Wheelers
    • 4-Wheelers
    • Automated Guided Vehicles
    • Energy Storage Systems
    • Industrial Applications
    • Outdoor Powered Equipment
    • Passenger and Commercial Vehicles
    • Unmanned Aircraft System
  • Company
    • About
    • Careers
  • Resources
    • Case studies
  • Eco System
BMS

BMS Block Diagram and Architecture: What Every Block Does and How They Connect

bms block diagram

Quick Read

A BMS block diagram is a simple map of how a Battery Management System works, showing each functional block and how power and data move between them. The key blocks are the Analog Front End for sensing cell voltage and temperature, the microcontroller for SOC, SOH and safety decisions, protection switches, cell balancing, current sensing and communication. The BMS keeps repeating a sense, process, decide and act cycle to protect the battery. Depending on pack size, the architecture can be centralised, modular or distributed.

A BMS block diagram is the fastest way to understand what a Battery Management System actually does  not as a list of features, but as an interconnected system where every block depends on every other. Whether you are designing a BMS, evaluating one, or integrating a battery pack into a larger system, the block diagram is where the engineering logic becomes visible.

This guide explains every block in a standard BMS architecture diagram, how signals flow between them, and how the architecture changes across centralised, modular, and distributed topologies.

What Is a BMS Block Diagram?

A BMS block diagram is a schematic representation of a Battery Management System’s functional architecture  showing each major functional block, the data and power connections between them, and the hierarchy of control from sensing through processing to output.

It is not a circuit schematic. A circuit schematic shows components, values, and connections at the component level. A block diagram operates one level of abstraction above that  shows functional units (the AFE, the MCU, the protection switch) and the signal and power paths between them, without detailing the internal circuit of each block.

What a Battery Management System Block Diagram Shows

A complete BMS block diagram shows:

  • The battery cells and modules being managed
  • The sensing layer  voltage, current, and temperature measurement
  • The processing layer  the microcontroller running state estimation and safety logic
  • The protection layer  switches that control charge and discharge paths
  • The balancing layer  passive or active circuits that equalise cell voltages
  • The communication layer  interfaces to the vehicle, charger, or external system
  • The isolation layer  monitoring the boundary between high-voltage and low-voltage domains
  • The power supply  the circuitry that keeps the BMS itself powered from the battery it manages

Battery Management System Block Diagram (Labelled)

┌─────────────────────────────────────────────────────────────┐

│                    BATTERY PACK                             │

│  ┌──────┐  ┌──────┐  ┌──────┐  ┌──────┐  ┌──────┐        │

│  │Cell 1│  │Cell 2│  │Cell 3│  │ … │  │Cell N│        │

│  └──┬───┘  └──┬───┘  └──┬───┘  └──┬──┘  └──┬───┘        │

│     │         │          │          │         │             │

│  ┌──┴─────────┴──────────┴──────────┴─────────┴──────────┐ │

│  │         ANALOG FRONT END (AFE)                        │ │

│  │   Cell Voltage Sensing │ Temperature Sensing          │ │

│  └──────────────────┬──────────────────┬─────────────────┘ │

│                     │ SPI / I²C         │                   │

│  ┌──────────────────▼──────────────────▼─────────────────┐ │

│  │              MICROCONTROLLER (MCU)                     │ │

│  │   SOC Estimation │ SOH Tracking │ Safety Logic        │ │

│  └──┬────────┬──────┬───────────┬──────────┬─────────────┘ │

│     │        │      │           │          │               │

│  ┌──▼──┐ ┌──▼──┐ ┌──▼──┐  ┌───▼───┐  ┌───▼────┐         │

│  │CELL │ │CURR │ │PROT │  │ ISO   │  │ COMMS  │         │

│  │BAL  │ │SENSE│ │SWITCH│  │MONITOR│  │CAN/UART│         │

│  └─────┘ └─────┘ └──┬──┘  └───────┘  └───┬────┘         │

│                      │                     │               │

│              ┌───────▼──────┐    ┌─────────▼──────┐       │

│              │  CHARGE /    │    │  VEHICLE ECU / │       │

│              │  DISCHARGE   │    │  CHARGER /     │       │

│              │  PORT        │    │  EMS / SCADA   │       │

│              └──────────────┘    └────────────────┘       │

└─────────────────────────────────────────────────────────────┘

How to Read the Diagram: Power Path vs Signal Path

A BMS block diagram carries two fundamentally different types of connections and reading them separately prevents confusion.

Power path: The route that energy travels  from battery cells through the protection switch to the charge or discharge port. This path carries high current and, in most EV and ESS applications, high voltage. The protection switches (MOSFETs or contactors) sit in this path and open or close based on commands from the MCU.

Signal path: The route that data travels  from sensors (AFE, current sensor, thermistors) to the MCU, and from the MCU to communication interfaces and output controls. Signal paths carry milliamp-level currents at low voltage. In a well-designed BMS, the signal domain is galvanically isolated from the high-voltage power domain for safety.

Reading the block diagram with this distinction in mind immediately clarifies which blocks are sensing and processing (signal path) and which are switching and converting (power path).

Block Diagram of BMS Explained: Each Block and Its Function

Each block in the diagram has a defined role. Working from the battery outward from cells to communication here is what every block does and why it sits where it does in the architecture.

Battery Pack and Cell Modules

The battery pack is the source and sink of all energy the BMS manages. Cells are connected in series to achieve the required pack voltage, and in parallel to achieve the required capacity. The BMS connects to the pack at the cell level  sensing voltage across each individual cell, monitoring temperature at multiple points within the pack structure, and controlling charge and discharge through switching elements at the pack terminals.

In modular pack designs, cells are grouped into modules. Each module may have its own local sensing circuitry (in distributed architectures) or connect directly to a centralised AFE board via a wiring harness (in centralised architectures).

Analog Front End (AFE): Cell Voltage and Temperature Sensing

The Analog Front End is the measurement layer of the BMS, the interface between the electrochemical world of the battery cells and the digital world of the microcontroller. AFE ICs (from suppliers including Texas Instruments BQ series, Analog Devices LTC series, Renesas) simultaneously sample all cell voltages in a module with measurement accuracy typically better than ±1 mV, communicate the results to the MCU via SPI or I²C, and report thermistor readings for temperature monitoring.

The AFE operates at cell potential  sitting at the high-voltage level of the cells it measures. It communicates with the MCU (which typically operates at low voltage, referenced to ground) through an isolated communication interface, maintaining the separation between the high-voltage cell measurement domain and the low-voltage processing domain.

Cell Balancing Block

The cell balancing block implements the circuitry that equalises cell voltages  either passive (switched resistors) or active (DC-DC converters, capacitor or inductor-based). The balancing circuits are controlled by the MCU based on real-time cell voltage data from the AFE. In passive designs, the balancing block consists of resistors and MOSFET switches co-located on the AFE or a dedicated balancing board. In active designs, it is a separate converter circuit with its own control interface to the MCU.We cover both methods in detail, including circuit topologies and when each makes sense, in Cell Balancing Explained: Active vs Passive Balancing for Lithium-Ion Battery Packs 

Current Sensing and Fuel Gauge Block

The current sensing block measures the current flowing in and out of the battery pack  the data that feeds directly into Coulomb counting for SOC estimation and into overcurrent protection decisions.

Shunt Resistor vs Hall-Effect Current Sensor

Shunt resistor: A precision low-value resistor placed in series with the current path. The BMS measures the voltage drop across the shunt (using Ohm’s Law: V = IR) to calculate current. Shunts offer high accuracy, low cost, and direct DC measurement. The tradeoff is ohmic power loss (I²R) in the shunt and the requirement for the measurement circuit to operate at pack potential  requiring isolation between the measurement point and the low-voltage MCU domain.

Hall-effect sensor: Measures the magnetic field generated by current flowing through a conductor without requiring ohmic contact with the power path. Hall-effect sensors provide galvanic isolation inherently  the measurement is physically separate from the current-carrying conductor. Better suited to high-voltage systems where placing a measurement circuit at pack potential creates design complexity. Less accurate than precision shunts at low currents but avoids the ohmic loss.

Temperature Monitoring Block

Negative Temperature Coefficient (NTC) thermistors distributed throughout the battery pack provide the BMS with real-time temperature data. The temperature monitoring block reads thermistor resistance and converts it to temperature values in the MCU. Thermistor count and placement are design parameters; more thermistors give better spatial resolution for detecting localised hotspots but add cost and wiring complexity.

Temperature data feeds into three BMS functions simultaneously: thermal protection (triggering cooling or disconnection at threshold temperatures), SOC estimation correction (cell capacity and voltage characteristics vary with temperature), and charge rate management (limiting charge current at low temperatures to prevent lithium plating, limiting discharge current at high temperatures to reduce heat generation).

Microcontroller (MCU): SOC, SOH and Safety Logic

The MCU is the processing core of the BMS, the block that turns raw sensor data into decisions. It receives cell voltages from the AFE, current from the current sensor, and temperatures from the thermistors, then runs:

State estimation algorithms  SOC (Coulomb counting with Kalman filter correction) and SOH (capacity and resistance tracking over cycle history). For a closer look at what these two metrics mean and how they’re calculated, read our article on What Are SOH and SOC in a Battery? How Are They Measured and Key Differences? 

Protection logic  comparing measured parameters against defined thresholds and generating protection commands when any threshold is exceeded.

Balancing control  determines which cells need balancing and activating the appropriate balancing circuits.

Communication management  formatting and transmitting battery state data over CAN, UART, or other interfaces, and receiving commands from external systems.

In ASIL-C functional safety applications, the MCU is typically a lock-step dual-core device with two identical cores running in parallel, comparing outputs to detect computational errors that could lead to safety-critical failures.

Protection and Cutoff Switches

The protection switches sit in the power path  between the battery cells and the charge or discharge terminals  and open or close based on commands from the MCU. In low-to-mid voltage applications (typically below 100V), back-to-back MOSFETs serve as the switching elements, providing microsecond-response-time protection with low on-state resistance. In high-voltage applications (above 100V, particularly in EVs and ESS), electromechanical contactors replace MOSFETs as the primary switching elements  providing the physical isolation and high-voltage capability that MOSFETs cannot match at kilovolt levels.

Two separate switches are typically used  one in the charge path and one in the discharge path  allowing the BMS to independently control charging and discharging, permitting charge while blocking discharge (or vice versa) for specific fault conditions.

Pre-Charge Circuit

When a high-voltage battery pack connects to a system with large input capacitance  a motor inverter’s DC bus capacitors, for example  the inrush current from instantly charging those capacitors through closed contactors can be large enough to weld the contactor contacts or damage the capacitors. The pre-charge circuit addresses this: a resistor in series with a pre-charge contactor limits inrush current during connection. The BMS sequence is: close pre-charge contactor (current-limited connection), wait until the bus voltage rises to near pack voltage, then close the main positive contactor, then open the pre-charge contactor. This sequence protects both the contactors and the downstream capacitors from inrush damage.

Isolation Monitoring Block

The isolation monitoring block continuously measures the insulation resistance between the high-voltage bus (battery pack positive and negative) and the vehicle chassis or system ground. In a healthy system, this resistance should be a very high  megaohm range  representing effective galvanic isolation between the high-voltage domain and any surface a person might touch.

Degradation in isolation resistance  from wiring insulation damage, coolant ingress, or connector corrosion  reduces this resistance toward dangerous levels. The BMS’s isolation monitoring function detects this reduction and triggers an alert or protective disconnection before isolation resistance falls to a level that creates electric shock risk. Isolation monitoring is a mandatory safety function for any BMS operating above 60V and is required for compliance with UN FMVSS, ECE R100, and IEC 62619 standards.

Communication Interface (CAN, SPI, I²C, UART)

The communication interface block is how the BMS talks to the rest of the world. Multiple interfaces typically coexist in a single BMS:

CAN 2.0 / CANopen  the primary vehicle communication interface, used to transmit SOC, SOH, pack voltage, current, temperature, fault status, and available power to vehicle ECUs, chargers, and motor controllers. CAN is robust, fast, and natively supported by automotive electronics.

SPI / I²C  lower-level internal interfaces used for communication between the MCU and AFE ICs, current sensor ICs, and other on-board peripherals. These are board-level interfaces, not external communication protocols.

UART is used for diagnostic communication, BMS configuration, and low-bandwidth external interfaces in non-automotive applications.

RS485 / Modbus  standard for ESS applications, used for communication between the BMS and inverters, EMS platforms, and SCADA systems.

As more of these interfaces connect to diagnostic tools, apps, and the cloud, protecting them becomes part of the design. Our article explains why in Your EV Battery Is Connected, But Is Cyber Security in Battery Management System (BMS) Strong Enough? 

How Signals Flow Through a BMS System Block Diagram

Signal flow in a BMS follows a consistent cycle: sense, process, decide, act.

Sense: AFE ICs continuously sample cell voltages and thermistor temperatures. The current sensor measures pack current. All measurements are timestamped and transmitted to the MCU at defined sampling intervals  typically every 10–100 ms for cell voltages, every 1 ms or faster for current.

Process: The MCU integrates incoming sensor data with its internal models. Current is integrated over time for Coulomb counting. Voltage and current are fed into the state estimation algorithm to update SOC. Historical capacity data is used to update SOH. All measured parameters are compared against protection thresholds.

Decide: The MCU determines required actions based on processed data  whether to activate a balancing circuit, adjust a charge rate limit, issue a warning to the external system, or trigger a protective disconnection.

Act: The MCU outputs commands to the appropriate blocks  activating a balancing MOSFET, transmitting a CAN message, reducing the maximum charge current setpoint, or opening the protection contactor. The cycle repeats continuously.

Example: What the BMS Does When a Cell Overheats

A practical walkthrough of the signal flow for a thermal protection event:

  1. A thermistor adjacent to a cell group registers elevated temperature. The AFE reads the thermistor resistance and transmits the temperature value to the MCU.
  2. The MCU compares the reported temperature against its threshold table. At 45°C, it sends a CAN message to the thermal management system commanding increased coolant flow.
  3. At 55°C, the MCU reduces the maximum charge and discharge current setpoints  derating power to reduce heat generation from internal resistance.
  4. At 60°C, the MCU sends a warning fault code via CAN to the vehicle ECU and activates a dashboard alert.
  5. At 65°C (hard protection threshold), the MCU commands the protection switch to open, disconnecting the pack from the load or charger. The BMS logs the fault event with a timestamp and the cell temperatures at the time of disconnection.
  6. When the pack cools below the recovery threshold (typically 50°C with hysteresis), the BMS permits reconnection after a defined delay.

The entire sequence  from thermistor reading to contactor opening  occurs within milliseconds.

BMS Architecture Diagram: Centralised vs Modular vs Distributed

Each architecture makes a different set of tradeoffs between cost, scalability, and fault tolerance. Starting with the simplest and working up in complexity:

Centralised BMS Architecture

In a centralized architecture, a single BMS master board handles all functions of cell voltage measurement via AFE ICs for all cells, current sensing, temperature monitoring, state estimation, protection switching, balancing, and communication  in one unit.

┌─────────────────────────────────────────────┐

│              CENTRALISED BMS                │

│  AFE → MCU → Protection → CAN             │

│  All cells wired to one board               │

└─────────────────────┬───────────────────────┘

                      │ Long wiring harness

              ┌───────▼───────┐

              │  Battery Pack │

              │  (all cells)  │

              └───────────────┘

Strengths: Lowest cost, simplest system, fewest components, straightforward fault management.

Limitations: Long wiring harnesses to all cells increase cost, weight, and potential failure points as cell count grows. Single point of failure for all BMS functions. Measurement accuracy degrades at high cell counts due to wiring resistance effects.

Best for: Small-to-medium packs  electric two-wheelers, three-wheelers, entry-level EVs, small stationary storage.

Modular (Master-Slave) BMS Architecture

In a modular architecture, standardised slave modules handle cell-level measurement and balancing for a fixed number of cells each. A master controller aggregates data from all slaves, runs system-level state estimation and protection logic, and manages external communication.

┌────────────┐   ┌────────────┐   ┌────────────┐

│ BMS SLAVE 1│   │ BMS SLAVE 2│   │ BMS SLAVE N│

│ AFE + BAL  │   │ AFE + BAL  │   │ AFE + BAL  │

└─────┬──────┘   └─────┬──────┘   └─────┬──────┘

      │                │                  │

      └────────────────┴──────────────────┘

                       │ Daisy-chain / isolated UART

              ┌────────▼─────────┐

              │   BMS MASTER     │

              │ MCU + SOC + CAN  │

              │ Protection Logic │

              └──────────────────┘

Strengths: Scales well to large cell counts. Shorter wiring per slave module. Master failure affects system management but slaves continue local protection. Standardised modules reduce design effort for different pack sizes.

Limitations: Higher system cost than centralised. Master-slave communication adds latency and potential failure points. More complex fault management across the master-slave boundary.

Best for: Mid-to-large EV packs, commercial vehicles, BESS rack systems, any application requiring scalability beyond what a single AFE chain can handle.

Distributed BMS Architecture

In a distributed architecture, small satellite boards mounted directly at each cell or cell group handle local voltage and temperature measurement. A master controller aggregates digital telemetry from all satellites over a digital communication bus, handling state estimation, protection decisions, and external communication.

[Cell 1]──[Sat 1]──┐

[Cell 2]──[Sat 2]──┤

[Cell 3]──[Sat 3]──┤  Digital bus (isolated)

   …             ├──────────────────────────┐

[Cell N]──[Sat N]──┘                          │

                                    ┌─────────▼─────────┐

                                    │    BMS MASTER      │

                                    │ MCU + SOC + CAN    │

                                    │ Protection + COMMS │

                                    └────────────────────┘

Strengths: Eliminates long analogue wiring harnesses  satellites communicate digitally. Best measurement accuracy for large packs. Highly scalable. Localised satellite failure affects only its cells, not the full system.

Limitations: Highest cost and system complexity. Digital communication bus between satellites and master must be designed for reliability and low latency. More hardware to qualify and test.

Best for: Large-format packs, grid-scale BESS, electric buses, high-voltage passenger EVs  where measurement accuracy, wiring mass reduction, and scalability justify the added complexity.

Which BMS Architecture Fits Your Pack?

Pack SizeCell CountRecommended Architecture
Small (24V–48V)Up to 16SCentralised
Medium (48V–200V)16S–100SCentralised or Modular
Large (200V–800V)100S–500SModular
Very Large (800V+, ESS)500S+Modular or Distributed

These ranges are a starting point rather than a rule. Most pack builders settle the architecture early, in discussion with their BMS manufacturer in India or abroad, because the choice affects wiring, enclosure design, and certification. 

BMS Block Diagram by Application

The core BMS block diagram adapts differently depending on the application it serves. Here is how the architecture shifts across three distinct use cases.

EV Battery Management System Block Diagram

An EV BMS block diagram adds several elements beyond the basic architecture: the pre-charge circuit for inverter bus capacitor management, isolation monitoring for passenger safety, CAN communication to vehicle ECU and onboard charger, and integration with the vehicle’s thermal management system (cooling pump and heater control outputs from the BMS).

The EV BMS must also handle high dynamic current profiles and rapid transitions between regenerative braking (charge current) and traction demand (discharge current)  requiring fast current sensing and MCU processing. Functional safety certification (ASIL B or ASIL C) is mandatory for automotive BMS, adding hardware redundancy and diagnostic coverage requirements to the architecture. For the vehicle-side view of these functions, read our article on What Is BMS in an Electric Vehicle? Functions, Benefits & Importance. 

Energy Storage (ESS) BMS Block Diagram

An ESS BMS block diagram replaces CAN with Modbus RTU or CANopen as the primary external communication interface  aligning with the inverters, EMS platforms, and SCADA systems used in stationary storage. The ESS BMS typically manages a larger cell count than an EV BMS (hundreds to thousands of cells in a rack system), favouring modular or distributed architecture.

ESS applications add requirements for extended float operation monitoring, long-duration SOH tracking (20-year project life), and communication with the site EMS for dispatch optimisation. The protection philosophy also differs; ESS contactors are typically larger and rated for higher interrupt capability than automotive contactors.

Low-Voltage BMS Block Diagram (12V, 24V, 48V Packs)

Low-voltage BMS designs (for e-bikes, small portable systems, and 48V light EVs) simplify the architecture meaningfully. Isolation monitoring is not required below 60V. Pre-charge circuits are typically unnecessary at low voltage and current. MOSFET protection switches are standard throughout the voltage range. Communication is often UART or SMBus rather than CAN.

The low-voltage BMS block diagram typically integrates AFE, MCU, MOSFET protection, and passive balancing on a single compact PCB; the entire BMS fits within the battery enclosure without external mounting requirements.

How to Draw a BMS Block Diagram (Step by Step)

With the blocks and architectures understood, here is how to build the diagram from scratch in a sequence that mirrors how BMS systems are actually designed.

Step 1: Define the battery pack. 

Start with the cells  number of series cells (S count), number of parallel cells (P count), chemistry, and nominal pack voltage. This determines the voltage domain the BMS must operate in and the protection switch technology required.

Step 2: Select the architecture. 

Based on cell count and application (centralised, modular, or distributed). This determines whether you need a master-slave communication layer.

Step 3: Draw the power path.

From pack positive terminal, through the positive protection switch, to the load/charge port. From pack negative terminal, through the current sensor and negative protection switch, to the load/charge port. Add the pre-charge circuit parallel to the positive contactor if required.

Step 4: Add the sensing layer. 

AFE ICs connected to each cell group in the series string. Thermistors distributed across the pack. Current sensor in the power path. All connected to the MCU via their respective interfaces (SPI/I²C for AFE, analogue input for thermistors and shunt, digital interface for Hall-effect sensor).

Step 5: Add the balancing block. 

Passive (resistors and MOSFETs per cell, controlled by AFE or MCU) or active (converter circuit with MCU control interface). Show connection to individual cell terminals.

Step 6: Add the MCU block. 

Central to the diagram, with connections to: AFE (SPI/I²C in), current sensor (in), thermistors (in), balancing circuits (control out), protection switches (command out), isolation monitor (in/out), communication interfaces (out).

Step 7: Add the isolation monitoring block. 

Connect it to the high-voltage bus and chassis ground, with a status output to the MCU.

Step 8: Add communication interfaces. 

CAN transceiver, UART, RS485  connected to the MCU and exiting the BMS to external systems (vehicle ECU, charger, EMS).

Step 9: Add the BMS power supply. 

The circuitry that derives low-voltage power for the MCU, AFE, and gate drivers from the battery pack itself. Typically a DC-DC converter stepping down from pack voltage to 3.3V or 5V for the logic domain.

Step 10: Label power paths and signal paths differently. 

Use solid lines for power paths (thick, showing current direction) and dashed or thinner lines for signal paths. Add voltage domain boundaries showing where isolation is required.

Conclusion

A BMS block diagram is the single most useful document for understanding how a Battery Management System functions as an integrated system rather than a list of features. It shows which blocks generate data, which blocks process it, which blocks act on it, and how the power path and signal path remain appropriately separated throughout.

Understanding the block diagram is essential for BMS selection, integration, and troubleshooting  and for communicating system architecture between hardware, firmware, and systems engineering teams. The architecture choice  centralised, modular, or distributed  cascades through every other design decision, from wiring harness design to fault management strategy.

Maxwell Energy’s BMS solutions are available across all three architectures, covering 24V to 1500V applications in EV, ESS, and industrial segments  with modular hardware and configurable firmware that can be adapted to the specific block diagram requirements of each application.

FAQ

1. What is a BMS wiring diagram?

A BMS wiring diagram shows the physical electrical connections between the BMS board and the battery pack  cell sense wires, thermistor wires, power connections, and communication harnesses. It is more detailed than a block diagram, showing wire gauges, connector types, and pin assignments rather than functional blocks.

2. What is 1S, 2S, and 3S in BMS?

The S count defines how many cells are connected in series in the pack. 1S is a single cell. 2S is two cells in series (doubling the voltage). 3S is three cells in series. The BMS must be specified to match the pack’s S count; a 3S BMS manages three series cells with three individual voltage measurement channels.

3. What is BMS and how does it work?

A BMS is a Battery Management System, the electronic and software system that monitors, protects, and manages a rechargeable battery pack. It measures cell voltage, current, and temperature; estimates State of Charge and State of Health; enforces protection limits; manages cell balancing; and communicates battery status to external systems.

4. How to design a BMS circuit?

Start with the battery specification (chemistry, voltage, current, cell count), then select AFE ICs, MCU, protection switches, and current sensor to match. Design the sensing layer, protection switching layer, and communication interface. Define protection thresholds for the target chemistry. Develop firmware for state estimation and protection logic. Validate against the target application’s certification requirements.

5. What is BMS in architecture?

In the context of BMS design, architecture refers to the structural organisation of the BMS how sensing, processing, protection, and communication functions are distributed across hardware. The three primary BMS architectures are centralised, modular (master-slave), and distributed.

6. What are the three types of BMS?

A centralized single board manages all cells. Modular slave modules handle cell groups; the master handles system logic. Distributed satellite boards at each cell group communicate digitally to a master controller.

7. How to design a BMS system?

Define the pack specification first. Select architecture based on cell count and application. Design hardware blocks in sequence sensing layer, MCU, protection switches, balancing, communication, power supply. Develop firmware for state estimation, protection, and communication. Validate the complete system against the target safety and regulatory standards before deployment.

“” “”

Related articles

Uncategorized

MOSFET vs Contactor Based BMS: What’s the difference?

In the electrifying world of Battery Management Systems (BMS), choosing between MOSFETs (Metal-Oxide-Semiconductor Field-Effect Transistors) and contactors can make or break your battery system’s performance. Buckle up as we dive into this comprehensive technical comparison

The latest insights, straight to your inbox

Registered Office

S. No. 218, Solitaire Office No. 5, Kalyani Nagar, Yerwada,Pune – 411 006, Maharashtra, India

Head Office, India

No. 24, 2nd Floor, Kalyani Platina Phase I, EPIP Zone Phase I, Whitefield, Bengaluru 560 066

Manufacturing Facility

Sarang Society, Near Gajanan Maharaj Mandir, Garkheda Road, Plot No. 41, CTS No. 15308/32, Chhatrapati Sambhajinagar, Maharashtra 431 009

image 56
image 55
Group 190072
Vector

Products

  • CT-Lite
  • CT-Lite+ 80A
  • CT-Safe
  • FS-LT
  • CT-Lite+
  • CT-Lite
  • CT-Lite+ 80A
  • CT-Safe
  • FS-LT
  • CT-Lite+
  • FS-XT
  • HP-Safe
  • SB-PR-I
  • IoT
  • FS-XT
  • HP-Safe
  • SB-PR-I
  • IoT

Company

  • Investor Relations
  • About us
  • Careers
  • Investor Relations
  • About us
  • Careers

Resources

  • Blog
  • Case studies
  • Upcoming projects
  • Blog
  • Case studies
  • Upcoming projects

Join us

  • Open Positions
  • Open Positions
We are hiring
2026 - Maxwell Inc. All Rights Reserved.
Linkedin
Linkedin

Make in India

top

Inactive

Simplifying IT
for a complex world.
  • About us
  • Why us
  • Team
  • Partners & Certifications
  • Reviews & Awards
  • About us
  • Why us
  • Team
  • Partners & Certifications
  • Reviews & Awards
Platform partnerships
  • AWS
  • Google Cloud
  • Microsoft
  • Salesforce

Inactive

Services
  • Managed Services
  • IT Consulting & Advisory
  • Cyber Security
  • Web Development
  • Mobile Development
  • Cloud Services
  • Managed Services
  • IT Consulting & Advisory
  • Cyber Security
  • Web Development
  • Mobile Development
  • Cloud Services
Business Challenges

Digital Transformation

Security

Automation

Gaining Efficiency

Industry Focus
  • Industry Manufacturing
  • Transportation Logistics
  • Healthcare
  • Banks & Insurance
  • Consulting Providers
  • Non Profit
  • Industry Manufacturing
  • Transportation Logistics
  • Healthcare
  • Banks & Insurance
  • Consulting Providers
  • Non Profit
View all